Metalshield® Epoxy Enamel Spray Paint
About Metalshield® Epoxy Enamel Spray Paint
Dulux Metalshield® Epoxy Enamel spray paint is a heavy-duty, anti-corrosive topcoat that is ideal for protecting metal surfaces from rust and corrosion. Use in combination with Metalshield® primers for industrial strength metal protection.
Downloads
Application
At a glance
- High-performance topcoat for metal protection
- Superior rust prevention system
- Maximum resistance to UV damage
- Silicone modified enamel
- Exceptional colour and gloss retention
- Pre-tinted colours
Areas to use
Surfaces
• Bare steel
• Wrought iron
• Galvanised iron
• ZINCALUME®
• Aluminium
• Copper
• Brass
• Stainless steel
• Metal
• Pre-painted metal surfaces
Previously Painted Surfaces
Pre-painted metal surfaces
1. Scrape off all loose and flaking paint.
2. Sand all surfaces to a flat finish.
3. Dust off.
4. If previously painted surface is in good condition then no primer is required.
Aged, lightly rusted surfaces, new bare steel, wrought iron
1. Remove any rust by scraping, sanding or wire brushing.
2. Wipe surface with mineral turpentine to remove any residual grease, oils and dirt.
3. Once dry, for maximum protection apply one coat of Dulux Metalshield® Etch Primer spray pack.
Galvanised iron, ZINCALUME®, aluminium, copper, brass, stainless steel
1. Clean surface with detergent and a Scotch-Brite® Pad to remove any grease, oils and dirt.
2. Rinse with clean water.
3. Once dry, apply one coat of Dulux Metalshield® Etch Primer spray pack.
4. Ensure the surface has thoroughly dried prior to application.
Brush, roller
Before spraying
• Shake can for at least three minutes after first rattle and regularly during use.
• Lower temperatures and high humidity will slow the drying and affect the gloss level.
• Avoid spraying when air or surface temperature is below 10°C or above 30°C.
Spray application
• Hold can upright 15 to 25cm from the surface.
• To ensure surface compatibility, test spray on an inconspicuous area.
• Spray with smooth, even strokes parallel to the surface.
• Apply with several light mist coats rather than one heavy coat, which can cause running and sagging.
After spraying
• Prevent blocking by turning the can upside down and spraying until clear gas emerges.
• Also wipe front of nozzle clean.
• Clean up overspray while it is still wet with mineral turpentine.
Unused paint
Storage
• Store in a cool, dry, well-ventilated place and and away from oxidising agents and corrosive materials.
• Protect from sunlight.
• Store away from sources of heat and/or ignition.
• Do not expose to temperatures exceeding 50°C.
Unused paint
Spray unwanted paint onto newspaper and allow to dry, and then disposed of via domestic waste collections.
Disposal of empty aerosol containers via domestic recycling programs differ between local authorities.
Check with your local council first. For more information on responsible disposal of paint and packaging visit paintback.com.au or painttakeback.co.nz
For more information visit painttakeback.co.nz
Empty paint containers
Empty paint containers:
Empty aerosol cans are recyclable via steel can recycling programs.
Disposal of empty aerosol containers via domestic recycling programs differ between local authorities.
Check with your local council first. For more information on responsible disposal of paint and packaging visit paintback.com.au or painttakeback.co.nz
Shop with us when you want, how you want.
DuluxTRADE Online
Download the app to access the benefits of a DuluxTRADE account on the go.
Get detailed information about the physical and chemical properties of our products.
Advice for those challenges that arise in your busy and varied days.
Access technical product information and create project specifications.